Коммутатор ЦОД MES5500-32
ЕРРРП (ТОРП): ТКО-649/21- Уровень:
- L3
- Пропускная способность:
- 6,4 Тбит/с
- Интерфейсы:
- 2х10G SFP+, 32х100G QSFP28, 1xOOB
- Питание:
- AC/DC, 2 сменных БП
Новинка
Описание
Коммутатор MES5500-32 — это высокопроизводительное устройство, оснащенное интерфейсами 40GBASE-R и 100GBASE-R и предназначенное для использования в операторских сетях в качестве устройства агрегации и в центрах обработки данных (ЦОД) в качестве Top-of-Rack или End-of-Row коммутатора.
Неблокируемая коммутационная матрица позволяет осуществлять корректную обработку пакетов при максимальной нагрузке, сохраняя при этом минимальные и предсказуемые задержки для всех типов трафика. Схема вентиляции front-to-back обеспечивает эффективное охлаждение при использовании устройства в условиях современных ЦОД.
Коммутаторы MES5500-32 имеют возможность использования схем вентиляции Front-to-Back и Back-to-Front, что обеспечивает эффективное охлаждение при использовании устройств в условиях современных ЦОД.Отказоустойчивость устройств обеспечивается резервированием источников питания (1+1) и применением сменных модулей вентиляции. Коммутаторы имеют возможность горячей замены модулей питания и вентиляционных модулей, обеспечивая бесперебойное функционирование сети оператора.
Поддержка технологии EVPN/VXLAN, реализованная в устройствах, позволяет создавать сети с простой, высокопроизводительной и масштабируемой архитектурой для центров обработки данных
Улучшенные программы гарантии и поддержки
Вы можете расширить базовый набор услуг платными сервисами
Узнать больше
Характеристики
- Интерфейсы:
- 2х10G SFP+, 32х100G QSFP28, 1xOOB
- Таблица MAC:
- 131072
- Динамическая маршрутизация:
- RIP/OSPF/IS-IS/BGP
- ARP:
- 65527
- Производительность:
- 6,4 Тбит/с
- IP-фабрики:
- EVPN/VXLAN
- Питание:
- AC/DC, 2 сменных БП
- Вентиляция:
- front-to-back/back-to-front
ECCM
Eltex Cloud Configuration Manager - облачная система управления сетевым оборудованием
Тех.характеристики
Если вы хотите ознакомиться с полным техническим описанием, воспользуетесь разделом "Документы и файлы" ниже
Интерфейсы
10/100/1000BASE-T (OOB)
1
10GBASE-R (SFP+)
2
40GBASE-R4 (QSFP+)/100GBASE-R4 (QSFP28)
32
USB 2.0
1
Консольный порт RS-232 (RJ-45)
1
Производительность
Пропускная способность
6,4 Тбит/с
Объём буферной памяти
24 МБ
Объем ОЗУ (DDR4)
8 ГБ
Объем ПЗУ (embedded uSSD)
8 ГБ
Таблица MAC-адресов
131072
Таблица VLAN
4094
Количество VRRP-маршрутизаторов
127
Link Aggregation Groups (LAG)
128, до 8 портов в одном LAG
Качество обслуживания QoS
8 выходных очередей на порт
Размер Jumbo-фреймов
10240 байт
Стекирование
8 устройства
Физические характеристики и условия окружающей среды
Питание
100–240 В AC, 50–60 Гц
36–72 В DC
Варианты питания
Один источник питания постоянного или
переменного тока
Два источника питания постоянного или
переменного тока с возможностью горячей замены
Аппаратная поддержка Dying Gasp
Нет
Рабочая температура окружающей среды
От 0 до +45 °С
Температура хранения
От -50 до +70 °С
Охлаждение
5 сдвоенных вентиляторов
Рабочая влажность
Не более 80 %
Габариты (Ш × В × Г)
440 × 44 × 534 мм
Комплектация
Базовый комплект, который поставляется вместе с устройством
Руководство по эксплуатации (по запросу)
Сертификат соответствия
Паспорт устройства
Комплект крепежа в 19"стойку
Консольный кабель RJ-45 (по запросу)
Дополнительно
Комплектующие, модули и программные опции, которые приобретаются отдельно
Бесплатно
Стандартная гарантия
до 5 лет
Расширенные программы гарантии
Хит
Бесплатно
В порядке очереди
Новосибирское время
Приоритетная поддержка
Новосибирское время
Приоритетная поддержка
Московское время
Поддержка
круглосуточная поддержка
Хит
Подмена оборудования на время ремонта с отправкой на следующий рабочий день
Предоставим новое оборудование на время ремонта
Документы и файлы
Версия ПО 6.6.5 R3 (дата публикации: 26.12.2024)
ZIP, 51.1 Mb
Файлы MIB (дата публикации: 26.12.2024)
ZIP, 1.41 Mb
Инструкция по обновлению версии ПО в сетевых коммутаторах MES5500-32 при переходе с версии 6.6.3.4 и более ранних на 6.6.3.5 (с поддержкой breakout) и более поздние (дата публикации: 05.09.2024)
PDF, 740 Kb
Инструкция по обновлению версии ПО в сетевых коммутаторах MES2300, MES3300, MES5312, MES53xxA, MES5400-xx (дата публикации: 18.11.2024)
PDF, 958 Kb
Данное ПО совместимо с другими моделями устройств
MES5305-48, MES5310-48, MES5300-24, MES5400-24, MES5400-48, MES5410-48, MES5300-48
Обновления ПО
Firmware Version 6.6.5.4
Added:
- Ability to configure OOB interface as a source-interface for SNMPv2;
- Ability to configure OOB interface as a source-interface for SNMPv3;
- SNMPv2 support in VRF;
- SNMPv3 support in VRF;
- GRE tunnel support;
- Hardware BFD implemented;
- Support for multihomed connections for EVPN/VxLAN scenario with Ingress Replication.
Fixed:
- Improved stability of peer-detection functionality in VPC;
- Erroneous removal of voice vlan from interface by timeout in the presence of port security settings;
- SSH session hangs due to an error in calculating Message authentication code in SSH packet.
Прошлые версии
Firmware Version 6.6.5
Added:
- Added support for BGP Route Map, Community List and AS-Path List in VRF;
- Added BFD support for BGP in VRF;
- Added BFD support for OSPF in VRF;
- Added support for encryption of the user's password using the SHA512/md5 algorithm;
- Added BFD support for IS-IS;
- Added the ability to change the ipv4 gateway address in EVPN type 5 routes;
- Added support for the RADIUS client in VRF;
- Added the ability to configure the source-interface OOB for SYSLOG;
- Added the ability to configure the OOB source-interface for TACACS+;
- Added BFD support for OSPF;
- Added support for VCT cable diagnostics for SFP-T;
- Added support for an extended number of UDBs in the ACL;
- Increased the number of ACEs in ACL to 512;
- Added support for filtering routes by the value of the as-path attribute in BGP;
- Added community support in BGP;
- Added the ability to configure the source-interface OOB for SNTP;
- Added support for SNTP operation in VRF;
- Added support for SYSLOG operation in VRF;
- Added support for the TACACS+ client in VRF;
- Added support for SSH server operation in VRF;
- Added ARP suppression support for EVPN/VXLAN.
Fixed:
- Fixed the process of removing the VRF setting from the OOB interface;
- Fixed the behavior in which STP root BPDU packets did not pass through the VPC peer-link;
- Fixed a reboot that occurred when the number of ACL rules with port-range was exceeded;
- Fixed L3VNI collaboration with VXLAN in multicast replication mode;
- Fixed incorrect operation of PBR with VRRP;
- Fixed device freeze when configuring SNMPv3;
- Fixed a behavior where a MAC-flapping storm started in a VPC;
- Fixed incorrect isolation of VPC groups from peer-link;
- Fixed a issue with OSPF neighbours breaking when CPU utilisation is high;
- Fixed issue with sending BGP update EVPN Type-2 when MAC address re-learning in a different ethernet-segment;
- Fixed issue with traffic switching via VRRP backup;
- Fixed problem with parasitic ICMP Redirect from VRRP backup when pinging a VRRP IP;
- Fixed a critical error occurring when CPU utilisation is high;
- Fixed critical error occurring when adding OUI for VOICE VLAN;
- Fixed critical error occurring when configuring sflow in stack;
- Fixed a critical error occurring when stack links are broken;
- Fixed critical errors occurring when building STP tree or VPC neighborhoods;
- Fixed L3VNI collaboration with VXLAN in multicast replication mode;
- Fixed PBR collaboration with VRRP;
- Fixed device freeze when removing ACL;
- Fixed device reboot related to the operation of the BGP protocol;
- Fixed device reboot when adding ACLs with UDP and TCP port ranges to the interface;
- Fixed device reboot when deleting VLAN bound to VXLAN;
- Fixed mac flapping between LAG when using VPC;
- Fixed incorrect addition of outgoing VRRPv2 protocol packets;
- Fixed a behavior in which STP root BPDU packets did not pass through the VPC peer-link.
Firmware Version 6.6.4
Added:
- The bit depth of the uptime counter has been increased;
- Added support for macro operation based on track status;
- Added support for displaying information about QSFP28 in the output of the show inventory command;
- Added support for J9285D DAC cables;
- Added VRRP support to VRF;
- Added support for tftp in VRF;
- Added VRF support for the OOB interface;
- Added the ability to disable sending an empty packet to check the availability of the TFTP server;
- Added route-map support for OSPF;
- Added support for policy base routing next-hop;
- Increased the number of BGP sessions to 64 for MES5400-xx and MES5500-32 devices;
- Added the ability to summarize routes in BGP;
- The value of the upper limit for the rate-limit has been increased;
- Added the ability to redistribute routes from eBGP to L3VPN;
- Added support for password encryption when logging commands;
- Added the possibility of simultaneous operation of MAC and IP access lists on interfaces;
- Added the ability to check the source mac address in the IP source-guard;
- Added the ability to limit the number of DHCP clients per port;
- Added the ability to send an snmp trap to the login/logout event.
Fixed:
- Software flow control is disabled for the console port;
- Fixed vulnerability of the Web interface;
- The position of the AAA command block in the configuration has been changed;
- Fixed the operation of the DHCP server when sending DHCP NAK packets;
- The operation of optical and copper switches in the same stack has been restored;
- Fixed an error that causes a cyclical reboot of a Slave unit in the stack when upgrading to version 6.6.3.8;
- Fixed rebooting of switches in the scheme with VxVLAN/EVPN when restarting the ospf process;
- Fixed single-hop BFD for eBGP neighborhoods;
- Fixed an error that caused the device to reboot when adding a non-existent VPC domain to the VPC group;
- Fixed an error that causes the role to be retransmitted after the Primary device is rebooted in the VPC;
- Fixed the problem of device freezing when flapping MLAG links in VPC;
- Fixed the problem of incorrect VPC assembly after restarting one of the paired devices;
- Fixed a cyclic reboot of the device when there is an ethertype switchport dot1q setting on the interface;
- Fixed an error in restoring the switchport default-vlan tagged command when updating software;
- Fixed an error where the L3 interface of the physical port did not switch to the Up state when rapid-pvst was enabled;
- Fixed the problem of blocking MLAG, after restarting it, in RPVST;
- Changed the default value of the spanning-tree cost parameter for 25G/40G/100G ports;
- Fixed spanning-tree cost calculation for port-channel interfaces;
- Fixed device reboot when polling the dot1dTpFdbEntry SNMP table;
- Fixed an error that occurs when deleting the SNMPv3 server settings from the configuration;
- Fixed an error when binding the ACL to the interface vlan.
Firmware Version 6.6.3.5
Added:
- Support for breakout mode on 100G ports (4x25G, 4x10G) on MES5400-XX, MES5410-48, MES5500-32;
- FEC operation support for 25G ports.
Fixed:
- Fixed switching part of the links to the UP status when using the FH-DP4T26QS05 40G QSFP/4 SFP+ Fang Zhang Copper Twinax Cable 5M cable.
Firmware Version 6.6.3
Added:
- Added support for displaying information about QSFP28 by the show inventory command;
- Added sending a bgp update when retraining a mac address from the evpn-vxlan type to static;
- Added sending a bgp update when retraining a mac address from the evpn-vxlan type to dynamic;
- Added the ability to configure the number of telnet/ssh authorization attempts before the TCP session is terminated;
- Added support for MAC-mobility mechanisms;
- Added information about the current MTU to the output of the show ports jumbo-frame;
- Added the ability to filter traffic by S-VLAN tags between ports, with Double QinQ configured;
- Added the ability to configure private-vlan in trunk mode;
- Added the ability to configure fast convergence timers for the OSPF protocol;
- Increased the number of OSPF processes to 20;
- Added support for selecting FEC modes on 25G interfaces.
Fixed:
- Fixed a bug that caused the device to reboot when receiving a Join/Leave packet from RP for S,G records;
- Fixed traffic degradation in the EVPN/VXLAN + symmetric IRB scheme when Spine-Leaf links are broken;
- Fixed an error that caused the device to reboot when removing the ACL from the vlan interface;
- Fixed a bug that caused the device to reboot when storm-control was set up;
- Fixed CLI hangup when configuring multicast group in Vxlan;
- Fixed an error that caused the device to reboot when the show ip ospf command was output with a certain device configuration;
- Fixed a bug that caused the private-vlan primary configuration to disappear from the configuration after a reboot;
- Fixed a bug that caused the backup switch in the stack to restart again after the first reboot;
- Fixed the problem of filtering stp BPDUs on ports with STP disabled and pvid other than default vlan;
- Fixed a situation where erps and flex-link were not activated due to a conflict with the already disabled STP protocol;
- Fixed an error that caused the device to reboot when repeatedly displaying information of show commands in a telnet session using scripts;
- Fixed an error copying files from the device via scp if there are directories in the file path;
- Fixed an error that caused the device to reboot when connected via SSH;
- Fixed errors that cause the device to reboot when connecting via SSH using the 3des encryption algorithm;
- Fixed errors that cause the device to reboot when connected via SSH;
- Fixed an error due to which, with some probability, 100G ports could not switch to the UP state when connecting QSFP28 FH-A100M3QQ03 and FH-A100M3QQ01.
Firmware Version 6.6.2.9
Fixed:
- Fixed an error disabling hardware routing in VRRP;
- Fixed the error of selecting the Endpoint address of the tunnel when rebuilding the IGP;
- Fixed a peer-link blocking error when receiving PVST bpdu;
- Fixed the SFP-T status error;
- Fixed the error of processing OSPF Hello packets;
- Fixed the collision of MAC addresses of VRRP processes;
- Fixed MD5 error for BGP neighbor's;
- Changed the MAC address of the OOB interface to the system one;
- Fixed the RPVST problem that causes SVI interfaces to be Down;
- Fixed a problem that leads to stack collapse with high traffic load on the CPU;
- Fixed a problem that causes ports to drop out of LAG when there is a high traffic load on the CPU;
- Fixed temperature display for all built-in MES5400-24 temperature sensors.
Firmware Version 6.6.2
Added:
- Added the option to select the checksum calculation method for VRRPv3;
- Added support for IP-MAC EVPN routes Type 2;
- Added the ability to change Administrative Distance for static routes and for OSPF routes;
- Added support for authentication in BGP;
- Added the ability to change the privilege level for commands;
- Added VRRP authentication;
- Added support for FangHang FH-DP10T30QQ03 100G QSFP28 Copper 3M DA module;
- The MTU size has been increased to 10240 bytes for transit routed traffic.
Fixed:
- Fixed behavior blocking the passage of a client ARP packet through a multicast VXLAN tunnel;
- Improved the stability of the ERPS sub-columns;
- Fixed a problem when copying configuration from BGP;
- Fixed the reboot of the backup unit in the stack when there is a negotiation bypass setting;
- Fixed an issue that causes the switch to reboot when polling it in the first seconds of booting via SNMP with OID: 1.3.6.1.4.1.35265.41.1.1.1.1.4.0.5.
- Fixed the problem of detecting link drop on a neighboring device using SFP-T;
- Fixed a possible hang when configuring VxLAN Multicast replication;
- Fixed SSH server freezing when receiving a package with an empty SSH version;
- Fixed a reboot that occurred when re-creating a VPC group;
- Fixed incorrect status of VPC groups after rebooting one of the devices in a VPC pair;
- Added support for joint operation of the VRRP and VPC protocols.
Firmware Version 6.5.2.1
Added:
- Added the ability to authorize input commands via the TACACS+ protocol;
- Added support for the NAS-ID (32) RADIUS attribute in Access-Request;
- IGMP snooping table size increased;
- Increased the number of LAG interfaces to 128;
- Added binding of Dying Gasp to OAM.
Fixed:
- Delays in switching traffic in the scheme with a VPC have been eliminated when one of the switches of the pair is rebooted;
- Fixed a bug with raising the link to SFP-T after the shutdown/no shutdown command;
- Fixed a bug in RPVST where the RPVST tree is built for a VLAN that is missing on the port;
- Fixed a reboot of the switch at the time of switching on the ERPS if there is an ACL binding to any port;
- Fixed switch reboot when arp table overflow;
- Fixed the appearance of Link flapping when using various DAC and SFP+ modules to connect to servers with an Intel X722 adapter;
- Fixed the hang of one device in the VPC pair after rebooting the second device;
- Fixed a bug in learning the mac address of a neighbor of a VPC pair on a peer link;
- Fixed incorrect cleaning of the arp table and output of the corresponding messages to the console.
Firmware Version 6.5.1.4
Fixed:
- Fixed incorrect disconnection of SFP-T when the port is turned off;
- Fixed non-connection of the link to the SFP-T after turning off/on the port;
- Fixed the problem of retraining MAC addresses on VPC devices of the pair.
Firmware Version 6.5.1.1
Added:
- Added the ability to configure the DHCP Option 82 format by templates;
- Added the possibility of simultaneous relabeling of VLAN ID, COS and DSCP via service policy;
- Added the ability to monitor the parameters of power supplies;
- Added the ability to configure storm control, rate-limit and policer in pps;
- Added the possibility of relabeling DSCP to COS traffic;
- Added Root guard for individual instances in mst;
- Added the ability to set 802.1p priority for VLAN management;
- Added the ability to configure SNMP trap to change the state for each port;
- Added support for Ethernet OAM;
- Added support for STP TC Protection;
- Added the ability to configure supported Ethertype for LAG;
- Added the ability to configure Lookup Length for the disposal of FDB for MES53xxA switches;
- Added logging when receiving STP BPDU with the Topology Check flag;
- Added information about the interface with the last accepted Topology code in the output of show spanning-tree;
- Added support for IGMP Snooping per-port Fast Leave.
Fixed:
- Fixed a problem with traffic transfer to VRF for stack units with backup and slave roles;
- Fixed the behavior in which the RPVST tree is built in VLANs forbidden on the port;
- Fixed hanging of one device from a VPC pair when rebooting;
- Fixed device reboot while using ERPS and binding the ACL to the physical interface at the same time.
Firmware Version 6.5.0.2
Added:
- Added stacking support;
- Added show-commands for displaying EVPN/VXLAN information;
- Added the ability to select algorithms for the SSH server;
- Added sending SNMP trap and syslog messages when the device is rebooted using the reload command;
- Added MSDP support;
- Added support for EVPN multihoming;
- The number of loopback interfaces has been increased to 64;
- Added support for Multicast VXLAN;
- Added support for IGMP static groups for PIM and IGMP-Proxy;
- Added support for Route Target Community;
- Added support for Symmetric IRB;
- Added support for PIM snooping;
- Added support for BGP in VRF;
- Added support for OSPF in VRF;
- Added support for static routes in VRF;
- Added display of BGP Community and Extended Community;
- Added the ability to configure the default route announcement condition in the BGP protocol.
Fixed:
- Fixed possible incorrect restart when the device is booting;
- Fixed error when ACL is deleted from vlan interface;
- Fixed displaying "Security level" field in the WEB interface;
- Fixed a problem with learning ARP for IP interfaces on Port-Channel;
- Fixed a critical error after the closed of a remote SSH session;
- Fixed error when viewing show inventory;
- Fixed error when loading configuration via TFTP;
- Fixed error when connecting to a device via SSH;
- Fixed local user authorization error when the Radius server is unavailable and the break method is enabled.
Firmware Version 6.4.1.3
Added:
- SFP+ Intel FTLX8571D3BCV-IT tranceivers are now supported;
- Added ability to ignore auto-negotiation on the ports.
Fixed:
- 8008 TCP port is now closed.
Firmware Version 6.4.1.2
Added:
- Added the ability to configure the default BGP route announcement;
- Added the ability to bind track to static routes;
- Added simplex communication mode for physical ports.
Fixed:
- Fixed reboot of the stack unit when PVST is enabled;
- Fixed incorrect output of information about CPU load;
- Fixed frequent change of port states in RPVST.